Search Results

THE NEW DIRECT-INJECTION diesel engines — the naturally aspirated 16000 and the turbocharged 21000 — were developed to power specific crawler and wheel vehicles built by Allis-Chalmers. Thus the original design and performance specifications were defined by the space available in these machines, and by the power and torque characteristics required by them. Also, the engines had to be suitable not only for commercial applications such as generator sets, shovels, and compressors, but also for oil field and marine service. Torque and speed requirements indicated that a 5¼-in. bore and 6½-in. stroke would give the desired performance. To meet the low heat rejection and good starting requirements, an open-chamber combustion system had to be used. The three-valve arrangement — two intake and one exhaust — was chosen because it offered low pumping losses and reasonable cost. This paper describes the design considerations and development work which produced the new diesel engines.*

PAPER DESCRIBES a procedure for the dynamical design of linear vibration isolators to protect a rigid equipment from the sinusoidal motions of a nonrigid supporting structure. A single degree of translational freedom of the equipment is assumed. Three types of data are required: (1) The equipment mass and its so-called fragility curve, (2) the mechanical admittance of the supporting structure and its amplitude of vibration when it supports no load, and (3) information to establish a minimum stiffness of the isolators. The procedure yields a region of permissible natural frequency and fraction of critical damping combinations for the isolator-mass system. The specification for the isolator dynamical requirements, including allowable tolerances, is derived from this region.*

The permanently increasing number of convenience and safety functions leads to higher complexity of in-car electronics and the rapidly growing amount of sensors, actuators and electronic control units places higher demands on high- speed data communication protocols. Safety-critical systems need deterministic protocols with fault-tolerant behavior. The need for on-board diagnosis calls for flexible use of bandwidth and an ever-increasing number of functions necessitates a flexible means of extending the system. None of the communication solutions available on the market until now (like CAN or TTP) have been able to fulfill all these demands. To solve these problems, BMW together with several semiconductor companies has developed a new protocol for safety-critical applications in automotive vehicles.

ALTHOUGH turbocharging of low-speed diesel engines has been used world-wide for a long time, it is only during recent years that it has been applied to high-speed diesels. This is the result of considerable engineering efforts from both the turbocharger and the diesel side that were put into the turbocharger, which appears to be a so utterly simple device. This paper de­scribes some of these engineering efforts. The basic design characteristics are developed with the point of view in mind that the turbo­charger has become much more than just an ad­ditional accessory. It is a vital component of the basic engine itself, contributing actively to the advancement of this prime mover. The basic de­sign characteristics center heavily around aero­dynamical and thermodynamical performance cri­teria which are so important in any advanced high-speed turbomachine.

Reduced emissions, improved fuel economy, and improved performance are a priority for manufacturers of internal combustion engines. However, these three goals are normally interrelated and difficult to optimize simultaneously. Studying the experimental heat release provides a useful tool for combustion optimization. Heavy-duty diesel engines are inherently transient, even during steady state operation engine controls can vary due to exhaust gas recirculation (EGR) or aftertreatment requirements. This paper examines the heat release and the derived combustion characteristics during steady state and transient operation for a 1992 DDC series 60 engine and a 2004 Cummins ISM 370 engine. In-cylinder pressure was collected during repeat steady state SET and the heavy-duty transient FTP test cycles.

AFTERCOOLING, coupled with higher pressure turbocharging can increase vehicle engine output. The author thinks that it is possible to anticipate diesel engines being run with compressors supplying air at pressure ratios higher than 2/1. Density ratio is the most important consideration in increasing pressure ratio, since the engine's output is dependent upon weight rather than volume of air supplied. Because the density of the compressed air is dependent upon its temperature at any pressure level, cooling the air after compression results in density increases. This paper describes various methods of after-cooling which increase engine output and fuel economy.

THE NEW CRC Diesel Engine Rating Manual is intended to furnish a universal language for identification of diesel-engine deposits and wear. Diesel-engine pistons are evaluated for lacquer deposits by utilizing an area demerit basis and color gradations of brown and gray from clean to black. In studying various means for evaluating thickness and texture of deposit in oil systems, it was decided that the scratch gage developed by the CRC Engine Deposit Rating Panel of the CRC-Motor Engine Varnish and Sludge Group was suitable for diesel engines. A procedure for establishing a volume factor which furnishes a weighted interpretation of the deposit was created.*

A “next generation” condensing heat exchanger for space systems has to satisfy demanding operational requirements under variable thermal and moisture loads and reduced gravity conditions. Mathematical models described here are used to investigate transient behavior of wetting and de-wetting dynamics in the binary porous system of porous tubes and porous cold plate. The model is based on the Richard's equation simplified for the zero-gravity conditions. The half-saturation distance or the zone of influence of the porous annular suction tubes on the cold-plate porous material will be in the range of 1 to 10 cm for the time scales ranging from 100 to 10,000 seconds and moisture diffusivity in the range of D = 10-4 to 10-6 m2/s.

Diesel engines are coming under stricter requirements to reduce emissions. particularly those of particulates and nitrogen oxides (NOx). Recently, the U. S. EPA put into place staged requirements for heavy duty diesel engines in urban bus applications which are aimed at ultimately bringing pre-1994 engines into particulate emissions compliance with 1994 heavy duty on-road truck standards (0. 1 g/bhp-hr TPM). This reflects the need to control emissions in crowded urban environments. Zirconia based ceramic combustion management coatings, although originally developed for adiabatic or low heat rejection engines to boost thermal efficiency, have also been shown to contribute to the reduction in diesel emissions. Heavy duty transient testing of rebuilt 2-stroke MUI diesel bus engines equipped with stabilized zirconia based coatings applied by thermal spray process have shown significant reduction in exhaust opacity relative to a baseline, uncoated engine.

Zero-offset in transducer output during airbag noise testing is often observed, but mostly ignored due to the lack of understanding of its causes and implications. In the field of high-g acceleration measurement, this phenomenon is well documented, and is referred to as zeroshift. Zero-offset occurs when a component in the measurement chain is exposed to some unexpected inputs which the component has not been designed to handle. These unexpected inputs can be mechanical, electrical, or optical. How the transducer reacts to such inputs and the amount of zero-offset produced depends on the sensing mechanism, material used, and the design of the component itself. This paper explores the causes of zero-offset from a general perspective, covering the entire measurement chain. Although much of the information and discussions are based on data obtained from acceleration measurement systems, the findings are applicable to other transducer types, such as pressure and acoustic measurements.

For human beings who have been reared on the earth with its 1 G gravitational field, the condition of weightlessness is a world with which we are unfamiliar. Even if the layout and equipment configuration of a spacecraft designed to compensate for operation under Zero-G conditions, there are some things which are not effective under actual weightless conditions. In the design of a manned spacecraft, it is necessary to accumulate design data on human performance in a weightless condition, then to undertake design evaluations and verification under weightless conditions. In this paper, testing for the purpose of evaluating the effectiveness of Zero-G simulation using neutral buoyancy, conducted first of all in Japan, and recommendations on the equipment and Facilities required to conduct such simulations, are described.

A zero-dimensional code is developed to simulate turbulent spray combustion and NOx and soot emission in direct injection diesel engines. The code consists of two major parts; mixing calculation for the probability density function (PDF) based on the multi-zone model by Hiroyasu et al., (1983) and the flame structure by the conditional moment closure (CMC) model (Klimenko & Bilger, 1999). The skeletal mechanism of n-heptane is employed with the elementary reaction steps for heat release and the NOx chemistry in GRI 3.0. The spray model accounts for evaporation and mixing based on momentum balance of the spray zones, while the CMC model incorporates the conditional flame structures with one fuel group or flame structure for each injection. The spatially integrated density-weighted PDF, F(η), is defined to represent inhomogeneous mixture distribution in the cylinder. The one-equation soot model is employed for prediction of the soot emission.

Zero-dimensional heat release rate models have the advantage of being both easy to handle and computationally efficient. In addition, they are capable of predicting the effects of important engine parameters on the combustion process. In this study, a zero-dimensional combustion model based on physical and chemical sub-models for local processes like injection, spray formation, ignition and combustion is presented. In terms of injection simulation, the presented model accounts for a phenomenological nozzle flow model considering the nozzle passage inlet configuration and an approach for modeling the characteristics of the Diesel spray and consequently the mixing process. A formulation for modeling the effects of intake swirl flow pattern, squish flow and injection characteristics on the in-cylinder turbulent kinetic energy is presented and compared with the CFD simulation results.

A zero-dimensional heat release model was developed for compression ignition engines. This type of model can be utilized for parametric studies, off-line optimization to reduce experimental efforts as well as model-based control strategies. In this particular case, the combustion model, in a simpler form, will be used in future efforts to control the combustion in compression ignition engines operating on gasoline-like fuels. To allow for a realistic representation of the in-cylinder combustion process, a spray model has been employed to allow for the quantification of fuel distribution as well as turbulent kinetic energy within the injection spray. The combustion model framework is capable of reflecting premixed as well as mixing controlled combustion. Fuel is assigned to various combustion events based on the air-fuel mixture within the spray.

In the developement process, the engineer is required to design, validate and deliver the components for manufacturing, in an as short as possible lead time. For that, the engineer may use some available tools to save not only time, but also cost. This work presents a zero prototype approach applyied to a plastic component, whose main accomplishment was the decreasing of lead time development due to the intensive use of virtual tools (CAD/CAE). As a result, the product was delivered in a short time, with no need of building physical prototypes, thus reducing development cost.

As the demand for more complex system development and the ever-increasing requirement for improvement in software productivity, the need for graphical programming or Zero-Hand Coding for automatic generation of controller software becomes highly desirable. The graphical programming must not be limited to the algorithm development which consists of the application modules but must be extended to the microcontroller platform, which include the middleware (i.e. operating system, I/O device drivers) and hardware. Automatic code generation is very important for programming the complex microcontroller internal parameters and registers. The combined software tool chain is to generate the final target specific executable code. This approach is very beneficial for system development, reduction of the development cycle and bridges the gap between control and software engineers reducing time, effort and cost of the production software.

Gasoline compression ignition shows great potential in reducing NOx and soot emissions with competitive thermal efficiency by leveraging the properties of gasoline fuels and the high compression ratio of compression ignition engines operating air-dilute. Meanwhile, its control becomes challenging due to not only the properties of different gasoline-type fuels but also the impacts of injection strategies on the in-cylinder reactivity. As such, a computationally efficient zero-dimension combustion model can significantly reduce the cost of control development. In this study, a previously developed zero-dimension combustion model for gasoline compression ignition was extended to multiple gasoline-type fuel blends and a port fuel injection/direct fuel injection strategy. Tests were conducted on a 12.4-liter heavy-duty engine with five fuel blends.

The thermal deflection associated with the conventional die heat treating procedure usually requires extra die grinding process to fine-tune the die surface. Due to the size of the production die, the grinding is time consuming and is not cost effective. The goal of the study is to develop a new die heat treating process utilizing the flexible laser heat treatment, which could serve the same purpose as the conventional die heat treating and avoid the thermal deflection. The unique look of the developed zebra pattern laser heat treating process is defined as the Zebra Line. The heat-treating parameters and processes were developed and calibrated to produce the laser heat treating on laboratory size dies, which were subjected to the die wear test in the laboratory condition. The USS HDGI 980 XG3TM steel was selected to be carried out on the developmental dies in the cyclic bend die wear test due to its high strength and coating characteristic.

The world's first six-speed automatic transmission for passenger cars was introduced to the market by ZF in 2001. The 6HP-family is based on a Lepelletier planetary gear set. An advanced version of these transmissions was launched in 2006. The 2nd generation offers significantly improved customer-relevant features such as reduced fuel consumption, response time and shifting speed. With regard to the increasing requirements especially in reduction of CO2 emissions, a new eight-speed transmission is now under development. The main targets for this transmission family are a further significant reduction in fuel consumption and emissions, good driving performance and state of the art driving comfort. The paper describes the transmission 8HP70, the schematic, main features and major design components. Key figures like transmission weight and size, fuel efficiency benefits and driving performance are shown compared to the 6-speed transmission of the 2nd generation.

The megatrends "reduction of emissions" and "fuel consumption reduction" play a predominant role in the development of powertrains. For transit buses this implies both the reduction of emissions and pollutions of the internal combustion engine, and, on the other hand, a further reduction of noise and brake dust. Also very important is the reduction of both fuel consumption and CO₂ emissions. For all these targets the actual developments on the engine side have led to great improvements in the last decades, but what can be mentioned for the other components of the powertrain, especially looking for transmissions? First of all the relevant trends for transit buses have to be considered: A large increase of the torque of the combustion engines during the last years has a big impact on the development of transmissions for buses.